TBT19252003液压起拨道器通用技术条件.pdf

ICS45.040
s24TB
中华人民共和国铁道行业标准

TB/'I'1925-2003
代替TB/T1925-1987

液压起拨道器通用技术条件

Generaltechnicalspecificationforhydraulictrackliftingandliningtool

2003-03-12发布2003-09-01实施

中华人民共和国铁道部发布
TB/P1925-2003

目次

前言······································，·······················，·········································⋯⋯n
1范围··，·················⋯⋯，··························，················································，·⋯⋯1
2规范性引用文件·········································································，·····················⋯⋯1
3术语和定义·····································································，································⋯⋯1
4型号编制··································································································⋯⋯2
5主要参数及安全使用限界···········································································⋯⋯，.⋯⋯，2
6要求·..............................................................................................................2
7试验方法·····，··································································································⋯⋯3
8检验规则···················，··················································································⋯⋯4
9标志和包装·······················································································，············⋯⋯4
7卫八1925-2003

前言

本标准代替TB/T1925-1987《液压起拨道器》。
本标准与TB/'r1925-1987相比，主要修改如下:
—标准名称改为《液压起拨道器通用技术条件》;
—增加了前言、术语和定义;
—调整了标准的编排结构，即将原标准第3章“试验方法和验收规则”分为“试验方法”和“检验规
则”两章，将其中的技术要求集中于本标准的第6章“要求”内;
—明确了按额定起道力和额定拨道力编写产品型号;
—产品规格由一种增加到五种;
—删除了有关工艺方面的要求，增加了铸件和焊接质量以及安全性能方面的要求，并规定进行逐
台检验;
—取消了容积效率计算和高温密封性能检查;
—将保压性能由抽样检验改为逐台检验;
—在型式检验项目中增加了超载检验。
本标准由铁道部标准计量研究所提出并归口。
本标准起草单位:哈尔滨铁路局、铁道科学研究院铁道建筑研究所、牡丹江铁路机具配件有限责任
公司(原林口液压起拨道器厂)。
本标准主要起草人:程勉海、付廷龙、宋慧京、韩忠福。
本标准于1987年首次发布，本次为第一次修订。
TB/If1925-2003

液压起拨道器通用技术条件

，范围

本标准规定了液压起拨道器(以下简称起拨道器)的有关术语和定义、型号编制、主要参数及安全使
用限界、要求、试验方法、检验规则、标志和包装。
本标准适用于铁路轨道作业用的液压起拨道器。

2规范性引用文件

下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件，其随后所有
的修改单(不包括勘误的内容)或修订版均不适用于本标准，然而，鼓励根据本标准达成协议的各方研究
是否可使用这